Doc modding Marantz imperial 7
- karatestu
- Posts: 5982
- Joined: Sun Jan 08, 2017 4:40 pm
- Location: North Yorkshire
- Has thanked: 1881 times
- Been thanked: 1418 times
Re: Doc modding Marantz imperial 7
Thanks for the encouragement and good luck messages.
Ok Doc, will transfer funds in the next week, thanks.
There are two visaton tweeters mentioned on HFS. G20 and G25. G25 is slightly larger - is this the one to go with if space allows ?
I may need some advice with getting the xover (the few components there are) correct.
Bass driver - nothing
Mid - parallel cap ?, maybe series resistor ?
Tweeter - series cap and resistor
Having never played with a 3 way before I have some homework to do.
Stu
Ok Doc, will transfer funds in the next week, thanks.
There are two visaton tweeters mentioned on HFS. G20 and G25. G25 is slightly larger - is this the one to go with if space allows ?
I may need some advice with getting the xover (the few components there are) correct.
Bass driver - nothing
Mid - parallel cap ?, maybe series resistor ?
Tweeter - series cap and resistor
Having never played with a 3 way before I have some homework to do.
Stu
DIY FREE ZONE
- Dr Bunsen Honeydew
- Posts: 30758
- Joined: Wed Jul 11, 2012 7:26 pm
- Location: Muppet Labs
- Has thanked: 0
- Been thanked: 48 times
Re: Doc modding Marantz imperial 7
G20 will be fine, or G25 if you want.
There will be two ways to do the bass and mid 1/ (Recommended) the drivers wired in series and no crossover components or padding. 2/ wired in parallel with a series capacitor of about 33mfd (adjust by ear) to the mid unit.
The tweeter done as usual with 3.3mfd cap and 12 ohm pad.
KISS applies (keep it simple)
There will be two ways to do the bass and mid 1/ (Recommended) the drivers wired in series and no crossover components or padding. 2/ wired in parallel with a series capacitor of about 33mfd (adjust by ear) to the mid unit.
The tweeter done as usual with 3.3mfd cap and 12 ohm pad.
KISS applies (keep it simple)
-
- Posts: 8586
- Joined: Thu Jul 12, 2012 7:16 am
- Has thanked: 24 times
- Been thanked: 399 times
Re: Doc modding Marantz imperial 7
When I built my 3 way floorstanders , I wired the 8 inch and 6 inch focal drivers in series with no capacitor and much preferred it , that was the first bit of advise the doc gave me nearly 8 years ago now .
but as always you should try for yourself for the sake of two 3.3uf capacitors [ about 10 quid from maplins}
but as always you should try for yourself for the sake of two 3.3uf capacitors [ about 10 quid from maplins}
- Dr Bunsen Honeydew
- Posts: 30758
- Joined: Wed Jul 11, 2012 7:26 pm
- Location: Muppet Labs
- Has thanked: 0
- Been thanked: 48 times
Re: Doc modding Marantz imperial 7
33mfd would be a lot more expensive for good ones. 3.3mfd tweeter, (approx) 33md mid.
-
- Posts: 8586
- Joined: Thu Jul 12, 2012 7:16 am
- Has thanked: 24 times
- Been thanked: 399 times
Re: Doc modding Marantz imperial 7
oops yes it would , the price I quoted was for 3.3uf not sure you get such a value from maplins
- Dr Bunsen Honeydew
- Posts: 30758
- Joined: Wed Jul 11, 2012 7:26 pm
- Location: Muppet Labs
- Has thanked: 0
- Been thanked: 48 times
- karatestu
- Posts: 5982
- Joined: Sun Jan 08, 2017 4:40 pm
- Location: North Yorkshire
- Has thanked: 1881 times
- Been thanked: 1418 times
Re: Doc modding Marantz imperial 7
Speakers turned up today. I should be happy but 2 of the front corners are damaged by parcelfarce. Got them from a charity and their packing was very poor , one cardboard box around each speaker and nothing else. I am a bit mad but cant be arsed sending them back. Some bodging required.
DIY FREE ZONE
- Dr Bunsen Honeydew
- Posts: 30758
- Joined: Wed Jul 11, 2012 7:26 pm
- Location: Muppet Labs
- Has thanked: 0
- Been thanked: 48 times
- karatestu
- Posts: 5982
- Joined: Sun Jan 08, 2017 4:40 pm
- Location: North Yorkshire
- Has thanked: 1881 times
- Been thanked: 1418 times
Re: Doc modding Marantz imperial 7
I am going to have a go at repairing them.
The front edges protrude 16mm in front of the baffle and one corner is damaged a good 12mm back ! the other speaker is not as bad.
I think there are two options.
1) Repair by gluing in some wood and finding some walnut veneer as close as a match as I can find
2) Remove the cabinet "bumper" that sticks out 16mm all the way around. This would bring it back to the same level as the front baffle. I would then probably paint or veneer the front baffle and the exposed chipboard that will be all the way around the perimeter of the cab. I could make new grilles that cover the entire front rather than the original ones that sit within the "bumpers". The original grilles are a bit grotty anyway.
The other problem I have come across is trying to fit all the drivers in. The 5" mid will be a problem and it wont fit in the port hole. I might have to do some serious bodging with this. I need more time to work this all out. Putting a whole new baffle on the front of the existing one may be an option here - a 19mm sheet of Baltic birch might do the job.
I have a lot of chin scratching to do.
Stu
The front edges protrude 16mm in front of the baffle and one corner is damaged a good 12mm back ! the other speaker is not as bad.
I think there are two options.
1) Repair by gluing in some wood and finding some walnut veneer as close as a match as I can find
2) Remove the cabinet "bumper" that sticks out 16mm all the way around. This would bring it back to the same level as the front baffle. I would then probably paint or veneer the front baffle and the exposed chipboard that will be all the way around the perimeter of the cab. I could make new grilles that cover the entire front rather than the original ones that sit within the "bumpers". The original grilles are a bit grotty anyway.
The other problem I have come across is trying to fit all the drivers in. The 5" mid will be a problem and it wont fit in the port hole. I might have to do some serious bodging with this. I need more time to work this all out. Putting a whole new baffle on the front of the existing one may be an option here - a 19mm sheet of Baltic birch might do the job.
I have a lot of chin scratching to do.
Stu
DIY FREE ZONE
- Dr Bunsen Honeydew
- Posts: 30758
- Joined: Wed Jul 11, 2012 7:26 pm
- Location: Muppet Labs
- Has thanked: 0
- Been thanked: 48 times