Modding Minstrels
Modding Minstrels
Along side my Allison 6 project I was thinking about the possibility of modding my Minstrels but I'm not really sure where to begin and what will be worth while. Any ideas on the best way of improving what is already a stunning pair of speakers???
Squeezebox Touch - Cambridge Audio Azur (pre) - Mycetias 250A Power Amp - Mycetias V2 Speakers
- wallace
- Posts: 980
- Joined: Thu Jul 12, 2012 9:03 am
- Location: Bridgwater ,Somerset.
- Has thanked: 0
- Been thanked: 0
Re: Modding Minstrels
I suggest a light application of a good wax polish,but not mr sheen.Other than that i leave them well alone.
Revox B795,,NVA PHONO 1,Teac PD-H500C,Squeezebox Touch,Bushmaster MKII,NVA AP70,LS5,Royd Minstrels i/c's SSC's. .
Sony Laptop,E-Dac, NVA AP10P, LS3,SSC,Royd Coniston R.Grado RS1
Sony Laptop,E-Dac, NVA AP10P, LS3,SSC,Royd Coniston R.Grado RS1
- Dr Bunsen Honeydew
- Posts: 30758
- Joined: Wed Jul 11, 2012 7:26 pm
- Location: Muppet Labs
- Has thanked: 0
- Been thanked: 48 times
- wallace
- Posts: 980
- Joined: Thu Jul 12, 2012 9:03 am
- Location: Bridgwater ,Somerset.
- Has thanked: 0
- Been thanked: 0
Re: Modding Minstrels
Why did Mr Royd put the wadding in,in the first place,was it just accepted practice then.??
Revox B795,,NVA PHONO 1,Teac PD-H500C,Squeezebox Touch,Bushmaster MKII,NVA AP70,LS5,Royd Minstrels i/c's SSC's. .
Sony Laptop,E-Dac, NVA AP10P, LS3,SSC,Royd Coniston R.Grado RS1
Sony Laptop,E-Dac, NVA AP10P, LS3,SSC,Royd Coniston R.Grado RS1
- Dr Bunsen Honeydew
- Posts: 30758
- Joined: Wed Jul 11, 2012 7:26 pm
- Location: Muppet Labs
- Has thanked: 0
- Been thanked: 48 times
Re: Modding Minstrels
FFS, how many times do we have to have this question!!!
Everyone puts wadding in, I think it has just became an accepted convention. All you have to do is take it out and tell me if I am right or wrong. If I am wrong put it back, small job.
Everyone puts wadding in, I think it has just became an accepted convention. All you have to do is take it out and tell me if I am right or wrong. If I am wrong put it back, small job.
- wallace
- Posts: 980
- Joined: Thu Jul 12, 2012 9:03 am
- Location: Bridgwater ,Somerset.
- Has thanked: 0
- Been thanked: 0
Re: Modding Minstrels
Ok Ok,That's me told ,I'm doing it now.....
Revox B795,,NVA PHONO 1,Teac PD-H500C,Squeezebox Touch,Bushmaster MKII,NVA AP70,LS5,Royd Minstrels i/c's SSC's. .
Sony Laptop,E-Dac, NVA AP10P, LS3,SSC,Royd Coniston R.Grado RS1
Sony Laptop,E-Dac, NVA AP10P, LS3,SSC,Royd Coniston R.Grado RS1
- wallace
- Posts: 980
- Joined: Thu Jul 12, 2012 9:03 am
- Location: Bridgwater ,Somerset.
- Has thanked: 0
- Been thanked: 0
Re: Modding Minstrels
I hope you have more luck than me,one speaker was fine ,but the other one had it stuck in and i only managed to get two thirds of it out.All now back together without any blood spilt.Having seen the thick steel plate on the rear panel i realize why these small speakers are so heavy.Now listening to Sarah K Water Falls.Early days yet,but everything seems to be a bit more in focus,or as Russ Andrews would say,the musicians appear to be playing better.
Revox B795,,NVA PHONO 1,Teac PD-H500C,Squeezebox Touch,Bushmaster MKII,NVA AP70,LS5,Royd Minstrels i/c's SSC's. .
Sony Laptop,E-Dac, NVA AP10P, LS3,SSC,Royd Coniston R.Grado RS1
Sony Laptop,E-Dac, NVA AP10P, LS3,SSC,Royd Coniston R.Grado RS1
- Dr Bunsen Honeydew
- Posts: 30758
- Joined: Wed Jul 11, 2012 7:26 pm
- Location: Muppet Labs
- Has thanked: 0
- Been thanked: 48 times
Re: Modding Minstrels
Some Royd have some steel plate in them but they would benefit from more, not just on the back panel, especially if wadding is fully removed. Other Doc Mods are mostly already done, the bass driver is doped, the crossover is minimal. The only other thing worth trying is blocking the port. This will tighten and tunify (is that a word) the bass but the speaker will need to be back further to the wall to get the balance back.